ClemCo Plumbing on a service call in Temecula, California
Leaks & Pipes

Leak Detection in Temecula

Find it before you cut. We locate hidden leaks with acoustic, pressure, and thermal equipment instead of opening walls and hoping.

TRUSTED BY OVER 1,000 CUSTOMERS ACROSS THE TEMECULA VALLEY

Overview

Find it before you cut. Acoustic, pressure, thermal, no guesswork.

The expensive part of a hidden leak is usually not the repair. It is the demolition done while looking for it.

A pinhole in a copper line is a modest fix once somebody can reach it. Four holes cut in drywall and a section of tile lifted while hunting for that pinhole is a very different bill, and most of it was avoidable.

Detection First, Demolition Second

Acoustic equipment picks up the sound a pressurised leak makes as water forces through a small opening, and that sound travels well through slab and wall. Thermal imaging finds the temperature signature of a hot water leak behind a surface. Pressure testing on an isolated section confirms whether that run is holding.

Used together, they locate the leak. Then, and only then, does anything get opened up, and only as far as the repair genuinely requires.

Check The Meter First

Before anything else, it is worth proving the leak exists. Turn off every fixture in the house, note the water meter reading, use no water for two hours, and read it again. If the number has moved, water is escaping somewhere.

That two-hour test costs nothing and occasionally reveals the culprit is a running toilet rather than anything buried, which is the best possible outcome.

What Does It Cost?

Detection is priced on the size of the property and how much isolation the system allows. It is a modest cost set against cutting open walls to search, and where we go on to carry out the repair the two are quoted together so you can see the whole picture before deciding.

Call (714) 394-5678 for a free assessment.

Get Help Now

Find it before you cut. Leak detection across Temecula, Murrieta, and San Diego County. Call (714) 394-5678.

Scope of Work

What's In Every Leak Detection Call

Located Before Anything Is Cut

Detection first, demolition second. That order keeps the repair small and means you are not paying to put right the search as well as the leak.

Several Methods, Cross-Checked

Acoustic listening, line pressure testing, and thermal imaging each show different things. Used together they confirm a location rather than suggesting one.

Slab Leaks Pinpointed

A leak under a concrete slab is the classic case for proper detection, because the cost of guessing wrong is a hole in your floor in the wrong place.

We Tell You What We Are Certain Of

If the equipment gives a clear answer you get a clear answer. If a wall needs opening to confirm, we say that plainly instead of manufacturing false confidence.

Straight Into The Repair

Once the leak is found we can carry out the repair in the same visit in most cases, so you are not booking a second company and waiting again.

How It Works

Our Step-By-Step Process

  1. Step 1

    Confirm There Is Actually A Leak

    Before hunting for a leak it is worth proving one exists, and the water meter settles it quickly. We shut every fixture, note the reading, leave the system untouched, and check it again. Movement with nothing running means water is escaping somewhere. This also tells us roughly how significant the leak is, which shapes how we search. Occasionally this step reveals the real culprit is a running toilet rather than a hidden pipe, which is a very good outcome for everybody.

  2. Step 2

    Narrow It Down By Zone

    We isolate sections of the system at the stop valves and repeat the pressure check on each, which tells us whether the loss is on the hot side or the cold, indoors or out, and often which part of the house. Irrigation is isolated and tested separately because exterior lines are a common and easily overlooked source. Narrowing the search area before bringing out the sensitive equipment makes the whole process considerably faster.

  3. Step 3

    Pinpoint With The Right Equipment

    Acoustic equipment amplifies the distinctive sound a pressurised leak makes as water forces through a small opening, which carries surprisingly well through slab and wall. Thermal imaging picks out the temperature difference a hot water leak creates behind a surface. Pressure testing on an isolated section confirms whether that run is holding. We use them together rather than relying on one, because agreement between two independent methods is what turns a likely spot into a confirmed one.

  4. Step 4

    Mark It And Explain It

    The location gets physically marked on the floor or wall, and we explain what we found, how confident we are, and what the repair will involve. You also get told honestly if the result is less than certain. Slab work in particular can involve a genuine judgement call, and you are entitled to know when you are being given a best assessment rather than a confirmed fact.

  5. Step 5

    Repair, With The Smallest Opening

    In most cases we go straight into the [repair](/services/water-leak-repair) at the same visit. Access is cut to the minimum the job actually requires. For a slab leak you will be given the real options, which are a spot repair through the slab, rerouting the line overhead or around, or repiping if the system has failed more than once. Each has different cost and disruption, and we will tell you which we would choose in your position.

Customer Reviews

What Our Neighbors Say

4.9 from 48 Google reviews
Same-Day Service Available

Ready For Leak Detection?

Call now for fast, honestly priced service across Temecula, Murrieta, and San Diego County.

FAQs

About Leak Detection

  • A water bill that jumps without a change in usage. The sound of running water when everything is off. A warm patch on a slab floor. Damp, staining, bubbling paint, or a musty smell with no visible source. Low pressure that has crept in gradually. Any one of those is worth investigating before it finds something structural.

  • In the large majority of cases, yes. That is the entire purpose of the equipment. Acoustic and thermal methods work through slab, tile, and drywall. Occasionally a confirmed location still needs a small opening to verify before committing to a repair, and we will tell you when that is the case rather than pretending otherwise.

  • A leak in a water line running underneath or within the concrete foundation. Common signs are a warm spot on the floor if it is a hot line, the sound of running water with everything off, unexplained damp at the edge of flooring, or a sudden jump in the bill. They matter because water under a foundation undermines it over time, so they should not be left.

  • Not necessarily. A single failure on an otherwise sound system can often be repaired at the spot, or the affected line rerouted, which avoids opening the floor entirely. A system that has produced several slab leaks is a different conversation, and at that point repiping usually costs less than continuing to chase individual failures.

  • Yes, and they are more common than people expect. An underground irrigation leak can waste a substantial amount of water without ever showing on the surface. We isolate the irrigation supply from the domestic supply first, which immediately tells us which side the loss is on.

  • Most residential detection is completed within one to two hours. A larger property, a leak under a slab, or a system with limited isolation valves can take longer. We will give you a realistic expectation before starting rather than an optimistic one.

Where We Do It

Leak Detection Across The Valley

Based in Temecula, covering the whole Temecula Valley and running south into San Diego County. Emergencies answered 24/7, free estimates on everything else.

Also covering Menifee, Wildomar, Lake Elsinore, Winchester, French Valley, Fallbrook, Bonsall, Escondido, San Marcos, Vista, Oceanside. Not sure if you're in range? Call (714) 394-5678 and ask.

24/7 Emergency Plumbing

Don't Wait. Call Now.

Open 24/7 for emergencies

Tap To Call (714) 394-5678